CCNA Practice Quiz: 200-301 Quiz 36

1. Which of the following IPv6 addresses is equivalent to the IPv4 loopback address of 127.0.0.1? *This question is required.

• FE80::1
• ::
• FF02::1
• ::1

2. Which of the following are true of OSPF configuration to enable two routers to become adjacent? (Choose two) *This question is required.

• The router ID configured on both routers must match.
• The process ID used to configure OSPF must match.
• Hello and dead timer intervals must match on all routers.
• The area assigned to each network must match.
• K values must match on both routers.

3. A set of routers and links that share the same link-state database information is known as what? *This question is required.

• Area
• Backbone area
• Intra-area route
• Inter-area route

4. You are implementing a wireless network inside a local office. You require a wireless link to connect a laptop in the administrator's office directly to a system in the sales department. In the default configuration, the wireless AP uses a 360-dispersed RF wave design. After installation, the signal between the two systems is weak, as many obstacles interfere with the signal.

Which of the following strategies could you try to increase signal strength? *This question is required.

• Increase the RF setting on the AP.
• Increase the RF power on the isotropic antenna.
• Replace the omni-directional antenna with a directional antenna.
• Replace the directional antenna with an omni-directional antenna.
• Increase the RF setting on the client system.

5. Which of the following recommendations should you follow when placing access points to provide wireless access for users within your company building? *This question is required.

• Place access points near outside walls.
• Place access points above where most clients are.
• Place multiple access points in the same area.
• Place access points in the basement.

6. You want to create an ACL statement that allows traffic from any network. Which network address and wildcard mask value should you use? *This question is required.

• 0.0.0.0 and 0.0.0.0
• 0.0.0.0 and 255.255.255.255
• 255.255.255.255 and 255.255.255.255
• 255.255.255.255 and 0.0.0.0

7. Which SNMPv3 security level requires authentication with a username, but does not implement encryption? *This question is required.

• authNoPriv
• authPriv
• noAuthnoPriv
• Community Name

8. You are configuring a new 2960 switch. You issue the following commands:

switch(config)#interface fast 0/15
switch(config-if)#switchport mode access
switch(config-if)#switchport port-security
switch(config-if)#switchport port-security maximum 1
switch(config-if)#switchport port-security mac-address sticky
switch(config-if)#switchport port-security violation protect  

You connect a hub with two workstations to port Fa0/15. You power on Device1 and then Device2. What will be the result? *This question is required.

• Frames from Device2 will be allowed; frames from Device1 will be dropped.
• Frames from both Device1 and Device2 will be allowed.
• Port Fa0/15 will be disabled, and no frames will be accepted or forwarded.
• Frames from Device1 will be allowed; frames from Device2 will be dropped.

9. Frank, an IT tech, works for the ABC company. His friend Joe, who works for the XYZ company, informs Frank that XYZ company has been hit by a new malware attack. What is the first thing Frank should do for the ABC company? *This question is required.

• Isolate all of ABC company's systems from the internet.
• Perform a penetration test to check for malware vulnerabilities.
• Verify that ABC company's anti-malware software is updated and running.
• Research the malware attack to verify what the attack does.

10. You have a secret key. Bob wants the secret key. He has threatened to harm your reputation at the office if you don't give him the secret key. What type of attack is Bob attempting to use? *This question is required.

• Rubber hose attack
• Brute force attack
• Trickery attack
• Social engineering attack