CCNA Practice Quiz: 200-301 Quiz 33

1. Which of the following accurately describe how switches and hubs work? (Choose two) *This question is required.

• A hub repeats frames to all ports, regardless of the destination address.
• A switch uses the logical addresses in a packet to send it through the correct port to all VLANs defined on that port.
• A switch simply receives signals and regenerates them.
• A hub uses the hardware address in the frame to forward it to the hosts on the VLAN that corresponds to that address.
• Switches use the hardware address in the frame to send frames only to the port where the device is attached.

2. Following are three banner types that can be configured on a router:

- exec
- motd
- login

If all three banners were configured, in which order would they display when a Telnet session is used to connect to the router? *This question is required.

• exec, motd, login
• motd, login, exec
• login, motd, exec
• login, exec, motd
• motd, exec, login

3. You have just connected a Windows workstation to the network. The workstation can communicate with all devices on the same subnet, but can't communicate with other devices on other subnets. You use the ipconfig command on the workstation and see the following:

C:ipconfig
Windows IP Configuration
Ethernet adapter Local Area Connection:
    IP Address . . . . . . . . . . : 192.168.1.100
    Subnet Mask. . . . . . . . . . : 255.255.255.0
    Default Gateway. . . . . . . . : 192.168.1.1

No other devices seem to have an issue. What is the most probable cause of the problem? *This question is required.

• The wrong default gateway address has been configured.
• The IP address is already used on the subnet.
• The default gateway router is down.
• The subnet mask is configured incorrectly.
• The cable connecting the workstation to the network is bad.

4. You are configuring OSPF for a single router with two interfaces, as shown in the image. Which network statement(s) would you use to configure both interfaces for OSPF for area 0? *This question is required.

• network 192.168.1.64 0.0.0.15 area 0network 192.168.1.128 0.0.0.7 area 0
• network 192.168.1.64 0.0.0.63 area 0network 192.168.1.128 0.0.0.31 area 0
• network 192.168.1.64 0.0.0.31 area 0network 192.168.1.128 0.0.0.15 area 0
• network 192.168.1.0 0.0.0.255 area 0

5. Which of the following is used on a wireless network to identify the network name? *This question is required.

• WEP key
• SSID
• WPA2 passphrase
• MAC address

6. Which of the following wireless security methods uses a common shared key configured on the wireless access point and all wireless clients? *This question is required.

• WEP, WPA Personal, WPA Enterprise, WPA2 Personal, and WPA2 Enterprise
• WPA Enterprise and WPA2 Enterprise
• WEP, WPA Personal, and WPA2 Personal
• WPA Personal and WPA2 Enterprise

7. You have a Catalyst 2950 switch with three defined VLANs: VLAN 1, VLAN 3, and VLAN 5. You connect the switch to another switch using the Fa0/1 interface and use the switchport mode trunk command for Fa0/1.

Assuming that the other switch has the default configuration, what will now pass through Fa0/1 on the switch? *This question is required.

• Traffic for all VLANs defined on the switch
• Traffic in all default VLANs, but not for VLAN 3 or VLAN 5
• Only traffic in VLAN 1
• No traffic

8. You check the time on a router and find that it is out of sync with the time on the other routers and switches in your network. To fix this issue, you decide to configure NTP on the router to get time from an internal authoritative (master) NTP server with an IP address of 172.17.8.254.

Which command should you use? *This question is required.

• ntp master 172.17.8.254
• ntp status
• ntp server 172.17.8.254
• feature ntp 172.17.8.254

9. Which of the following best describes an antivirus sensor system? *This question is required.

• A collection of software that detects and analyzes malware
• Software that is used to protect a system from malware infections
• Analyzing malware's code to understand its purpose without running it
• Analyzing malware by running and observing its behavior and effects

10. Part of a penetration test is checking for malware vulnerabilities. During this process, the penetration tester needs to manually check many different areas of the system.

After these checks are completed, which of the following is the next step? *This question is required.

• Document all findings
• Run anti-malware scans
• Isolate the system from the network
• Sanitize the system