CCNA Practice Quiz: 200-301 Quiz 17

1. You have a small network with two switches, SwitchA and SwitchB. MDI-X is not enabled on either switch. Each switch has three client computers connected. IP addresses have been assigned to various devices as follows:

WrkA_1, WrkA_2, and WrkA_3 are connected to SwitchA, while WrkB_4, WrkB_5, and WrkB_6 are connected to SwitchB. All of the devices are configured to operate within the same subnet.

You need to connect SwitchA and SwitchB so that workstations connected to SwitchA can communicate with workstations connected to SwitchB. What should you do?

• Connect SwitchA and SwitchB using a straight-through cable.
• Connect SwitchA and SwitchB to a router using a crossover cable on each side.
• Connect SwitchA and SwitchB to a router using a straight-through cable on each side.
• Connect SwitchA and SwitchB using a crossover cable.

2. You are the senior network administrator for a large company. A junior administrator from one of your field offices sent you a router that he thinks is faulty. He says the router always uses default settings and boots to setup mode even though he has verified that startup-config contains the correct values.

What is the most likely source of the problem?

• There is no space available in NVRAM.
• The NVRAM chip is faulty, preventing the router from loading the configuration.
• The router configuration register is set to bypass startup configuration.
• Startup-config in NVRAM is corrupt and must be erased and restored from backup.

3. Which command would you use to show you the following information in a table?
 

• Feature name
• Enforcement
• Evaluation
• Subscription
• Enabled
• RightToUser

• show license UDI
• show license history
• show license feature
• show license

4. During the initial setup of a router, which of the following commands would set the host name as LAS?

• Router(config)#hostname LAS
• Router(config)#host LAS
• Router>ip dns LAS
• Router>host LAS

5. Kathy executed the show interfaces command on a router and reviewed the output. Which output indicates a Layer 1 problem with the Serial0/1/1 interface?

• Serial0/1/1 is administratively down, line protocol is down.
• Serial0/1/1 is up, line protocol is up, ping succeeds, but a Telnet connection can't be established.
• Serial0/1/1 is down, line protocol is down.
• Serial0/1/1 is up, line protocol is down.
• Serial0/1/1 is up, line protocol is up, but ping fails.

6. When attempting to make a Telnet connection to a remote router, the connection fails. You check the interface status on your local router and find the following:

Serial0/1/0 is up, line protocol is up
   Hardware is GT96K Serial
   Internet address is 192.168.2.1/24
   MTU 1500 bytes, BW 1544 Kbit, DLY 20000 usec,
   reliability 255/255, txload 1/255, rxload 1/255
   Encapsulation HDLC, loopback not set
   Keepalive set (10 sec)... (additional output omitted)

You ping the remote router, but that fails as well. At which layer of the OSI model does this problem originate?

• Layer 1
• Layer 2
• Layer 3
• Layer 7

7. Your router generates a log message with a severity level of 1. What does this indicate?

• The message is only informational in nature.
• A critical condition exists.
• The system is unusable.
• Immediate action is needed.

8. You are configuring a router to redirect and consolidate log messages to a Syslog server. The router has multiple interfaces. However, you want all log messages being sent to the Syslog server to be seen as coming from the same IP address on the router, regardless of which interface the message actually exits the router from.

Which command is used to accomplish this?

• logging source-interface < interface >
• logging host < address >
• logging trap < level >
• show logging

9. Which of the following are configuration management tools? (Choose two)

• Playbook
• Cookbook
• Manifest
• Ansible
• SaltStack

10. Arranging multiple automated tasks together to create a workflow is known as what?

• API
• Configuration management
• Orchestration
• Automation